ISO/TS TECHNICAL SPECIFICATION 15827 First edition 2007-02-01 Road vehicles Test procedures Evaluating small female dummy arm and forearm interactions with driver frontal airbags and side airbags Vehicules routiers — Méthodes d'essai- Evaluation des interactions du bras et de I'avant-bras du mannequin femme de petite taille avec les sacs gonflables conducteur frontal et latéral Reference number ISO/TS 15827:2007(E) @ ISO 2007 ISO/TS 15827:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2007 - All rights reserved ISO/TS 15827:2007(E) Contents Page Foreword. iv Introductior 1 Scope 2 Normative references 3 Terms and definitions. 4 Testdevices 4.1 Hybrid Ill small female dummy ... 4.2 siD-lls small adult/adolescent side impact dummy .. 4.3 SAE small female instrumented arm and the enhanced airbag interaction arm 5 Instrumentation... 5.1 Hybrid ill small female dummy...... 5.2 SID-lls small adult/adolescent side impact dummy 5.3 SAE small female instrumented arm ... 5.4 Impactresponsemeasurements... 5.5 Dummy injury criteria .. 6 Conditionofthetestvehicle. 6.1 General conditions . 6.2 Seat adjustment . 6.3 Steering wheel adjustment . 6.4 Pedal adjustment. 6.5 Dummytesttemperature 6.6 Electrical grounding .... Test configurations.. 7.1 Driverfrontalairbagtests 7.2 Side airbag static deployment tests . 8 8 Test procedure 9 Bibliography 10 ion'ghts reserved ISO/TS 15827:2007(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies (Iso member bodies). The work of preparing International Standards is normally carried out through IsO non-governmental, in liaison with iso, also take part in the work. iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lE Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a technical committee may decide to publish other types of normative document: an ISO Publicly Available Specification (ISO/PAs) represents an agreement between technical experts in an isO working group and is accepted for publication if it is approved by more than 50 % of the members of the parent committee casting a vote; committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for