ISO/TS TECHNICAL SPECIFICATION 10811-1 First edition 2000-06-01 Mechanical vibration and shock - Vibration and shock in buildings with sensitive equipment Part 1: Measurement and evaluation Vibrations et chocs mécaniques - Vibrations et chocs dans les batiments abritant des équipements sensibles - Partie 1: Mesurage et évaluation Reference number E ISO/TS 10811-1:2000(E) ISO @ ISO 2000 y IHS under ted without license from IHS Not for Resale ISO/TS 10811-1:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The isO Central Secretariat accepts no liability in this area. Adobe is a trademarkof Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event ?ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland @ ISO 2000 - All rights reserved ermittedwithoutlicense from IHS Not for Resale ISO/TS 10811-1:2000(E) Contents Page Foreword. Introduction 1 Scope 2 Normative reference. 3 Vibration wave forms 4 Measurement and analysis.. 4.1 General considerations.. 4.2 Instrumentationrequirements 4.3 Analysis ..... 4.4 Comparison with other analysis methods . 4.5 Statistical considerations.. 4.6 Calibration and accuracy... 5 Test report Annex A (informative) Definition of response-equivalent peak velocity spectrum.. Annex B (informative) Algorithms for filter calculations.. 12 Bibliography .. ili d by IHS under se from IHS Not for Resale ISO/TS 10811-1:2000(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedout throughISOtechnica committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a technical committee may decide to publish other types of normative document: parent committee casting a vote; committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed every three years with a view to deciding whether it can be transformed into an International Standard. Attention is drawn to the possibility that some of the elements of this part of IsO/Ts 10811 may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO/TS 10811-1 was prepared by Technical Committee ISO/TC 108, Mechanical vibration and shock, Subcommittee Sc 2, Measurement and evaluation of mechanical v