ISO/IEC INTERNATIONAL STANDARD 7816-2 Second edition 2007-10-15 Identification cards Integrated circuit cards Part 2: Cards with contacts Dimensions and location of the contacts Cartes d'identification - Cartes a circuit integré - Partie 2: Cartes a contacts Dimensions et emplacements des contacts Reference number ISO/IEC 7816-2:2007(E) IEC Tso @ ISO/IEC 2007 IHS under Not for Resale ISO/IEC 7816-2:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO/IEC2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's memberbody in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO/IEC 2007 - All rights reserved I without license from IHS Not for Resale ISO/IEC 7816-2:2007(E) Contents Page Foreword iv Introduction 1 Scope 2 Normative references .. 3 Dimensions of the contacts. 4 Number and location of the contacts .. 5 Location of contacts relative to other technologies Annex A (informative) Usage of the contacts.... .5 Annex B (informative) Location of possible conductive zones. Bibliography..... CopyrightInternatinal Oorganizain for standardization All rights reserved ili IHS under se from IHS Not for Resale ISO/IEC 7816-2:2007(E) Foreword Commission)formthespecializedsystemforworldwidestandardization.Nationalbodiesthataremembersof ISOorTECparticipateinthedevelopmentofInternationalStandardsthroughtechnicalcommittees technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with IsO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standardsadoptedbythejointtechnicalcommitteearecirculatedtonationalbodiesforvoting.Publicationas an International Standard requires approval by at least 75 % of the national bodies casting a vote. ISO/IEC 7816-2 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification. This second edition cancels and replaces the first edition (IsO/lEC 7816-2:1999), which has been technically revised.ItalsoincorporatesmaterialextractedfromISO/lEC7816-2:1999/Amd.1:2004. ISO/lEc 7816 consists of the following parts, under the general title Identification cards — Integrated circuit cards: Part 1: Cards with contacts —Physical characteristics Part 2: Cards with contacts Dimensions and location of the contacts Part 3: Cards with contacts —Electrical interface and transmission protocols Part 4: Organization, security and commands for interchange Part 5: Registration of application providers Part 6: Interindustry data elements for interchange Part 7: Interindus