ISO/IEC INTERNATIONAL STANDARD 23004-7 First edition 2008-02-15 Information technology Multimedia Middleware - Part 7: System integrity management Technologies de l'information—Intergiciel multimedia- Partie7:Gestionde I'integritedesysteme Reference number ISO/IEC 23004-6:2008(E) IEC ISO ISO/IEC2008 ISO/IEC23004-6:2008(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISo Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In COPYRIGHTPROTECTEDDOCUMENT ISO/IEC2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's memberbody inthe country of the requester ISO copyright office Casepostale56.CH-1211Geneva20 Tel. + 41 22 749 0111 Fax + 4122 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ISO/IEC 2008 -All rights reserved ISO/IEC23004-7:2008(E) Contents Page Foreword iv Introductior 1 Scope 2 Normative references 3 Termsanddefinitions.. 3.1 Specification terms and definitions. 3.2 Realization terms and definitions. 4 Abbreviatedterms 5 Overview ofinterfacesuites. 6 Integrity Management interface suites. 8 6.1 Interface suites forextraction and modification ofthe software configuration 6.2 Management activation interface suites 29 6.3 Support interface suites .39 7 Realization overview 49 7.1 Introduction. 49 7.2 SystemIntegritymanagementmechanisms .49 7.3 Roles in System Integrity Management..... 50 8 System Integrity Management realization.... 51 8.1 Structural view... 51 8.2 Behavior View.. 56 8.3 Deploymentview 60 8.4 Scenarios.. .64 AnnexA(informative)M3Wcomponent models.. ..65 AnnexB (informative)Examplediagnostic checks.. 67 AnnexC (informative)Examplescenarios... AnnexD (informative)Integrity Management exampleXML schema definitions. 72 Bibliography.... nAll rights reserved ili ISO/IEC23004-7:2008(E) Foreword Iso (the International Organization for Standardization) and IEc (the International Electrotechnical Iso or IEC participate in the development of International Standards throughtechnical committees established by the respective organization to deal with particular fields of technical activity. IsO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental technology,ISO and IEChaveestablisheda jointtechnical committee,ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the Iso/lEc Directives, Part 2 The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote Attention is drawn to the possibility that some of the elements of this part of ISO/lEC 23004 may be the ISO/IEC 23004-7 was prepared by Joint Technical Commitee ISO/IEC JTC 1, Information technology, Subcommittee SC29, Coding of audio,picture, multimediaand hypermedia information. ISO/IEc 23004 consists of the following parts, under the general title Information technology- Multimedia Middleware Part1:Architecture P