BS ISO 2332:2009 BRITISH STANDARD Agricultural tractors and machinery - Connection of implements via three- point linkage Clearance zone around implement ICS 65.060.01 BSi NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW British Standards BSISO2332:2009 National foreword This British Standard is the UK implementation of ISO2332:2009. It supersedes BS 6509:1984 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee AGE/6, Agricultural tractors and forestry machinery. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard Amendments/corrigendaissuedsincepublication was published under the authority ofthe Standards Policy and Strategy Date Comments Committee on 28 February 2009 BSI 2009 ISBN978058056216 7 BS ISO 2332:2009 ISO INTERNATIONAL STANDARD 2332 Third edition 2009-01-15 Agricultural tractors and machinery - Connection of implements via three-point linkageClearance zone around implement Tracteurs et materiels agricoles-Liaisons des instruments par I'attelage troispoints-Zonede degagement autourde I'instrument Reference number ISO 2332:2009(E) O @ ISO 2009 BS ISO 2332:2009 ISO2332:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either so at the address below or ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 4122 749 0111 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ Is0 2009All rights reserved BSISO 2332:2009 ISO2332:2009(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the memberbodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO2332 was prepared by Technical Committee ISO/TC 23,Tractors and machinery for agriculture and forestry,SubcommitteeSC4,Tractors. This third edition cancels and replaces the second edition (iSO 2332:1993), which has been technically revised. ISO 2009 - All rights reserved ii BS ISO 2332:2009 BS ISO 2332:2009 ISO 2332:2009(E) INTERNATIONALSTANDARD Agricultural tractors and machinery Connection of implementsviathree-pointlinkageClearancezone around implement 1 Scope This International Standard specifies the clearance zone around an implement for attachment to the three- point linkage of an agricultural wheeled tractor. and alsowhere implement couplers complying with ISO11001-1,ISO11001-2,ISO11001-3and IsO 11001-4 are used. 2 Normativereferences references, only the edition cited applies. For undated references, the latest edition of the referenced ISO730:2009,Agriculturalwheeled tractors—Rear-mounted three-point linkageCategories1N,1,2N,2, 3N,3,4Nand4 IsO11001(allparts),Agriculturalwheeledtr